Oxidation‐led decomposition of hexagonal boron nitride coatings on alloy substrates at 900 °C: Ti‐6Al‐4V

Hexagonal boron nitride (h‐BN) coatings on Ti‐6Al‐4V substrates undergo complete decomposition in air at 900 °C. This fate is similar to that of this ceramic material on chromia‐former alloys, and unlike that of a mass of powder treated in isolation. As the ceramic and alloy oxidize concurrently, outwardly diffusing aluminum (III) ions but not the predominant titanium (IV) ions react with the boron trioxide that forms around the h‐BN basal plane peripheries. Resultant aluminum borate is incorporated into the growing scale and the boron trioxide diffusion barrier is depleted. By this mechanism, the oxidation of h‐BN is maintained at an enhanced rate, until both this material and its oxide completely decompose. Liberated nitrogen from the oxidation of h‐BN can enter the underlying scale as a randomly distributed solute in rutile solid solution. The post‐coating oxide‐atmosphere interface comprises elongated aluminum borate crystallites protruding through at the boundaries between 3–5 at% nitrogen‐doped rutile grains. It differs significantly from that of oxidized, uncoated Ti‐6Al‐4V, which is occupied by a thin α‐alumina layer atop rutile. This interface does not change with an additional 72 h of heat‐treatment.     

Fe-Si-B非晶带材高温氧化行为及回收工艺

??In order to reduce the oxidative burning loss of Fe78Si9B13 amorphous ribbon in the recovery process?? the oxidation behavior of Fe78Si9B13 amorphous ribbon was studied. The results show that the oxidation of Fe78Si9B13 amorphous ribbon at high temperature is related to the heating rate. The oxidation weight gain of Fe78Si9B13 amorphous ribbon at 5 and 10K/min from room temperature to 1223K are 44% and 31% respectively. There is an oxide layer with loose texture and a small amount of microcrack at the interface between the sample and atmosphere by SEM. The oxide layer contains a large amount of Fe2O3 and a little SiO2 by XRD. Oxidation kinetics curve shows that the oxidation weight gain of the samples follows a linear rule within 5hours at 1073 and 1173K?? then a parabolic rule. At 1273K?? however?? it only follows a linear rule?? meanwhile the oxidation speed is very fast?? with the oxidation weight gain reaches 40% in 12min. The oxidation weight gain in the amorphous ribbon recycling process can be reduced through cutting down the furnace gas temperature?? compressing the waste ribbon and unqualified products in the packaging process and blowing argon to reduce the partial pressure of oxygen in the furnace. Thus the slag decreases to 9-10g when 1kg waste ribbon is recovered?? and the Si content of liquid alloy increases to 8. 9%.     

Insight into selective oxidation of dual-phase steel after annealing in pure H2 atmosphere at different heating rates and temperatures

In this paper, the oxidation behaviors of DP980 advanced high strength steel (AHSS) are studied during annealing in a hydrogen atmosphere with different temperatures and heating rates. It is revealed that with the increase in holding time, the different heating rates affecting the surface oxide precipitation on the strip surface will be weakened. Mass transfer of Mn in heating, soaking, and cooling stages has been considered to illustrate the effect of heating rate on the oxide morphology of steel. And then, the Wagner model and aluminothermic reaction kinetics were performed to discuss the transition from external to internal and maximum reduction diameter of MnO oxidation.     

碳纤维/乙烯基酯树脂复合材料拉伸性能研究

研究了碳纤维进行氧化处理、铺层形式,以及紫外光照射和不同溶液介质浸泡处理等,对碳纤维/乙烯基酯树脂复合材料拉伸性能的影响。结果表明:碳纤维最佳氧化工艺为浓硝酸氧化1 h,空气氧化温度250℃,空气氧化30 min。碳纤维最佳铺层设计为[0°,0°,45°]2s。随紫外光照射时间增加,复合材料拉伸强度呈先增后降趋势,120 h时达最大值。溶液介质浸泡会降低复合材料的拉伸强度。温度相同溶液介质不同时,复合材料在NaOH溶液中拉伸强度降低程度最大,温度提高会加速复合材料失效老化。     

Physicochemical Properties,Lipid Oxidation,and Fatty Acid Composition of Sausage Prepared with Meat of Young Nellore Bulls Fed a Diet with Lauric Acid

This study evaluates the quality of sausage obtained from the meat of Nellore cattle fed diets containing different levels (0, 5, 10, and 15 g per kg total DM) of lauric acid (C12:0) from palm kernel cake. A linear reduction (p ≤ 0.05) in lipid oxidation, as reflected by linear decreases in the lightness (L*), yellowness (b*), and saturation (C*) color parameters, is observed on days 7, 14, and 21 of maturation of sausage, and these decreases are accompanied by linear increases in the redness (a*) color and the linoleic (C18:2n–6) and linolenic (C18:3n–3) fatty acid contents. The inclusion of lauric acid in the diet induces linear reductions in the shear force and cooking loss and does not significantly affect various indices, including the centesimal composition, water activity, water holding capacity, composition of most fatty acids (FA), hypocholesterolemic‐to‐hypercholesterolemic FA ratio, atherogenicity, thrombogenicity, and desirable fatty acids. The use of dietary lauric acid from palm kernel cake is recommended at doses up to 15 g per kg because its presence reduces lipid oxidation and improves color parameters, softness, and linoleic and linolenic FA without affecting the FA composition of sausage from Nellore bull's meat. Practical applications : Sausages are products manufactured from chopped or ground meats packaged into animal casings. This product appeared in Brazil through the adaptation of traditional recipes brought by German and Italian immigrant families to weather conditions and the national palate. However, due to its production characteristics, sausage can become a product with lipid characteristics that are undesirable for human consumption. The inclusion of lauric acid (C12:0) in the animal diet might change the biohydrogenation process in the rumen, improve the quality of the deposited FA and reduce lipid oxidation in sausage manufactured from meat. The FA composition and physicochemical properties of sausage predict its acceptance by the consumer market. An optimal advantage would be achieved if these products can be used as not only preservatives but also functional ingredients with antioxidant properties and products for the treatment of metabolic syndrome and cardiovascular diseases through atherogenic action.     

铜基化合物的可见光催化研究进展

与传统贵金属光催化剂相比，铜基光催化剂具有价格低廉、绿色环保、反应条件温和、光催化活性可调节等优势，受到合成化学家们广泛关注。本文简述了铜基催化剂的光催化历史，回顾了近五年来铜基化合物在可见光催化领域的研究成果与进展，总结了铜基催化剂的独立光催化机理与协同光催化机理；简要阐述了铜催化剂在不同类型反应中的应用，重点讨论了铜(Ⅰ)催化剂在烯烃官能化、碳-碳偶联、碳-杂偶联、原位催化等反应中的应用研究，表明铜基化合物在光催化合成领域具有很大的应用潜力。对未来的研究工作进行了展望，指出拓展催化剂的反应适用性、探索催化剂的氧化还原能力、进一步开发催化剂在手性合成中的应用将是该领域的研究重点。     

铝空气电池用6061和7075铝合金阳极电化学性能

研究了工业6061铝合金（6061）、航空7075铝合金（7075）和纯铝作为铝空气电池阳极材料的电化学性能，分析其作为阳极的可行性及适用环境。进行了阻抗、极化曲线和恒电流放电实验并进行了表面表征，计算了在40～120mA/cm²电流密度下连续恒流放电的阳极能量密度。用电子探针显微镜（EPMA）对电极表面形貌进行了研究，用波谱分析仪（WDS）进行表面分析。研究结果表明，合金元素在电池放电过程中会改变阳极的表面特性。6061中合金元素含量对电池阳极材料的性能产生了积极影响，使得合金的表面放电面积变大，放电均匀，更适合作为铝空气电池阳极材料。     

短程反硝化耦合厌氧氨氧化工艺及其应用前景研究进展

短程反硝化以其碳源消耗量、废污泥产量、温室气体排量极低及无需曝气等优势，被认为是最具研究潜势的厌氧氨氧化底物供给技术，成为近年来研究热点。本文首先介绍了短程反硝化工艺原理；其次从污泥源、反应时间、碳源类型、碳源量及pH等5个方面总结了影响短程反硝化工艺启动因素；随后综述了短程反硝化耦合厌氧氨氧化工艺的重要研究进展，同时指出了耦合工艺实验研究与工程应用的不足，并提出了解决实验与工程应用缺陷的方案；最后展望了耦合工艺处理城市污水和工业硝酸盐废水的可行性及应用前景，认为全面分析工业硝酸盐废水化学组分与基于分子生物学水平的宏基因组学测序、元转录组学技术是未来耦合工艺同步处理城市污水和工业硝酸盐废水的研究重点。